Toggle navigation
Home
Article Category
Question Papers
General Knowlege
Popular Pages
Multiple Choice Question in 049
Multiple Choice Question in
Multiple Choice Question in 2016
Multiple Choice Question in TRADES-INSTRUCTOR---GR-II---SMITHY---TECHNICAL-EDUCATION
Multiple Choice Question in -current-affairs-2016
Question Answer in ASSISTANT-PROFESSOR---COMPUTER-SCIENCE-AND-ENGINEERING---TECHNICAL-EDUCATION
Multiple Choice Question in ASSISTANT-PROFESSOR---COMPUTER-SCIENCE-AND-ENGINEERING---TECHNICAL-EDUCATION
Multiple Choice Question in english
Multiple Choice Question in abbreviations-abbreviations-m
Multiple Choice Question in SSC CHSL 7 March 2018 Morning Shift
Multiple Choice Question in 072/2016
Question Answer Bank
Multiple Choice Question Bank
Question Answer Category
Multiple Choice Question Category
Home
->
Multiple Choice Questions
1. A load of 1960 N is raised at the end of a steel wire. The minimum diameter of the wire so that stress in the wire does not exceed 100 N/mm2 is :
(A): 4.0 mm
(B): 4.5 mm
(C): 5.0 mm
(D): 5.5 mm
(E): 6.0 mm
Previous Question
Show Answer
Next Question
Add Tags
Report Error
Show Marks
Write Comment
Type in
(Press Ctrl+g to toggle between English and the chosen language)
Post reply
Comments
Tags
Show Similar Question And Answers
QA->The Election Commission of India raised the cap of minimum votes of a political party must secure in election to get the status of a state party or maintain it further. The new minimum limit is ___ percent of the total valid votes polled:....
QA->If an officer is appointed to hold full charge of another post in addition to his own, he will be eligible for special allowance as a percentage of the minimum of the scale of pay of that post. This percentage shall not exceed:....
QA->If an officer is appointed to discharge the current duties of another post in addition to his own, he will be eligible for a special allowance as a percentage of the minimum of the scale of pay of the additional post. This percentage shall not exceed:....
QA->Any industry located in a rural area which produces any goods or renders any service with or without the use of power and in which the fixed capital investment per head of a worker does not exceed one lakh rupees is known as:....
QA->When the estimate of a public work does not exceed ……… it can be arranged by short tender quotation.....
MCQ->A load of 1960 N is raised at the end of a steel wire. The minimum diameter of the wire so that stress in the wire does not exceed 100 N/mm2 is :....
MCQ->A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that of brass bar is 3000 mm2. These are subjected to a compressive load 100,000 N. If Eb = 0.2 MN/mm2 and Eb = 0.1 MN/mm2, the stresses developed are:....
MCQ->A shaft is subjected to a maximum bending stress of 80 N/mm2 and maximum shearing stress equal to 30 N/mm2 at a particular section. If the yield point in tension of the material is 280 N/mm2 and the maximum shear stress theory of failure is used, then the factor of safety obtained will be....
MCQ->A close-coiled helical spring has 100 mm mean diameter and is mada of 20 turns to 10 mm diameter steel wire. The spring carries an axial load of 100 N Modulus of rigidity is 84 GPa. The shearing stress developed in the spring in N/mm2 is....
MCQ->A mild steel bar of square cross-section 40 mm x 40 mm is 400 mm long. It is subjected to a longitudinal tensile stress of 440 N/mm2 and lateral compressive stress is 200 N/mm2 in perpendicular directions. E = 2 x 10-5 N/mm2, μ = 0.3. What is the approximate elongation of tht bar in the longitudinal direction ?....
×
×
Type The Issue
×
Your Marks
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use
Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...
Privacy
|
Terms And Conditions