61351. The horizontal axis of an oscilloscope is normally calibrated in units of ________.
61352. The combination of waveforms consisting of the given figures 1 and 2 is generally referred to as ________.
61353. The digit that changes most often when counting is called the ________.
61354. Memory devices that use electronic latching circuits are called ________.
61355. A microprocessor that performs only specific, dedicated tasks is also called a ________.
61356. The decimal system is composed of ________ symbols.
61357. The manner in which a digital circuit responds to an input is the circuit's ________.
61358. The given figure is most likely a ________.
61359. A(n)________ is not a functional unit of a computer.
61360. The duty cycle of a square wave is ________.
61361. If a HIGH logic level is assigned a binary zero (0), and a low level is assigned a binary one (1), the logic is called ________.
61362. The quantity represented by #1 in the given figure is ________.
61363. A binary number can be converted to be viewed on a 7-segment display by a(n) ________.
61364. The CPU contains all the circuitry for ________.
61365. Demultiplexing is a logic function that ________.
61366. In ________ the quantities are not represented by continuously variable indicators.
61367. A continually variable, proportional indicator is a(n) ________ representation.
61368. The control and arithmetic/logic units are often considered as one unit called the ________.
61369. A microcontroller would not be used in a(n) ________.
61370. ________ is the highest-value seven-bit binary number.
61371. The systems shown in the given figure communicate using ________.
61372. The set of instructions for a computer is called a(n) ________.
61373. The controls on an oscilloscope that will help obtain a stable display are in the ________.
61374. The value of the data shown in the given figure is ________.
61375. To determine which of two binary numbers is larger, you could use a(n) ________.
61376. In ________ transmission, a single conductor is used.
61377. In a negative logic system, the area represented by #3 in the given figure would be the ________ level.
61378. The area represented by #4 in the given figure is the ________ level.
61379. Other ________ are often used to interpret or represent binary quantities for the convenience of the people who work with and use these digital systems.
61380. In a positive logic system, the HIGH level is usually represented by ________.
61381. A set of instructions for a computer is called a(n) ________.
61382. Any number with an exponent of zero is equal to:
61383. In the decimal numbering system, what is the MSD?
61384. Which of the following statements does NOT describe an advantage of digital technology?
61385. The generic array logic (GAL) device is ________.
61386. The range of voltages between VL(max) and VH(min) are ________.
61387. A 0.01-F capacitor is recommended by TTL manufacturers for ________ the power supply.
61388. Why does the data sheet for the 7476 only give a minimum value for the clock pulse width (both HIGH and LOW)?
61389. Why is the Schmitt trigger needed in the 60-Hz TTL-level clock pulse generator?
61390. The main concern when using a pull-down resistor is:
61391. Look up the propagation delay from the clock to the output for the 7476. Are the HIGH-to-LOW and LOW-to-HIGH propagation delays the same?
61392. What would be the output voltage of a 7814 voltage regulator?
61393. The purpose of a pull-up resistor is to keep a terminal at a ________ level when it would normally be at a ________ level.
61394. Setup time specifies:
61395. Can the automatic RC circuit be used to set a flip-flop rather than reset the flip-flop?
61396. A Schmitt trigger:
61397. A settable flip-flop's normal starting state when power is first applied to a circuit is always the ________ state.
61398. In the automatic reset circuit for a flip-flop, how long does it take the capacitor to completely charge?
61399. The output of a standard TTL NAND gate is used to pull an LED indicator LOW. The LED is in series with a 470- resistor. What is the current in the circuit when the LED is on?
61400. When the inputs to a flip-flop are changing at the same time that the active trigger edge of the input clock is making its transition, this condition is called:
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use
Powered By:Omega Web Solutions