1. The metal is subjected to mechanical working for





Write Comment

Type in
(Press Ctrl+g to toggle between English and the chosen language)

Comments

Tags
Show Similar Question And Answers
QA->The resilience of a material is considered when it is subjected to :....
QA->First American President who was subjected to impeachment is ?....
QA->WHICH METAL IS KNOWN AS " WONDER METAL "....
QA->WHICH METAL IS KNOWN AS METAL OF FUTURE....
QA->WHICH METAL IS KNOWN AS THE " MAGIC METAL OF LIFE "....
MCQ->The simplest method of welding two pieces of metal together is known as pressure welding.The ends of a metal are heated to a white heat-for iron,the welding temperature should be about 1300C-in a flame.At this temperature the metal becomes plastic.The ends are pressed or hammered together,and the joint is smoothed off.Care must be taken to ensure that surfaces are thoroughly clean first,for dirt will weaken the weld.Moreover,the heating of iron or steel to a high temperature cause oxidation,and a film of oxide is added to the heated surfaces.For this reason,flux is applied to the heated metal.At welding heat,flux melts and the oxide particles are dissolved in it together with any other impurities which may be present.The metal surfaces are pressed together,and the flux is squeezed out from the center of the weld.A number of different types of weld may be used,but for fairly thick bars of metals,a vee-shaped belt should be normally employed.It is rather stronger than ordinary butt weld. The simplest way of welding two pieces of metal together is....
MCQ-> Solve the questions based on the information provided in the passage below: Six engineers Anthony, Brad, Carla, Dinesh, Evan and Frank are offered jobs at six different locations –England, Germany, India, Australia, Singapore and UAE. The jobs offered are in six different branches, and are based on their competence as well as preference. The branches are IT, Mechanical, Chemical, Electronics, Metallurgy and Electrical, though not necessarily in the same order. Their placements are subject to the following conditions:i.The engineer in the Electrical Department is not placed in Germany. ii.Anthony is placed in Singapore while Dinesh in UAE. iii.Frank is not in the Metallurgy Department but Brad is in the Chemical Department. iv.Evan is placed in the Mechanical Department while Frank is offered a job in Australia. v.The only department offering jobs in India is the Chemical Department while there are no vacancies for IT in Singapore. vi. Anthony is interested in IT and Electrical Department while Frank is interested in IT and Mechanical Department. Both of them settle for the options available based on their interests in the locations allotted to them. vii. In recent years, UAE has emerged as a hub for metallurgy exports and thus recruitment is done for the same while all mechanical posts are in England.Who joined the Electronics Department?
 ....
MCQ-> Study the given information carefully to answer the question that follow: An organisation consists of 2400 employees working in different departments viz HR, Marketing, IT Production and Accounts The ratio of male to female employees in the organisation is 5:3 Twelve per cent of the males work in the HR department Twentyfour per cent of the females work in the Accounts department.The ratio of males to females working in the HR department is 6:11 One-ninth of the females work in the IT department.Fortytwo per cent of the males work in the production department the number of females work in the production department is ten per cent of the males working in the same The remaining females works in the Marketing Department The total number of employees working in the IT department is 285 Twenty two per cent of the male working in the Marketing department and remaining work in the Accounts departmentThe number of males working in the IT department forms approximately what per cent of the total number of males in the organisation ?
 ....
MCQ->The metal is subjected to mechanical working for....
MCQ->Assertion (A): In many materials, dielectric polarization causes mechanical distortion.Reason (R): If dielectric polarization causes mechanical distortion then mechanical distortion must cause dielectric polarization.

....
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use
DMCA.com Protection Status Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...Privacy | Terms And Conditions