1. When the weld is made from left to right, it is known as back-hand welding.



Write Comment

Type in
(Press Ctrl+g to toggle between English and the chosen language)

Comments

Tags
Show Similar Question And Answers
QA->In a row of students, Sherin is 12th from the left and Athira is 19th from the right. If they inter change their positions, Sherin becomes 16th from the left. Then, what will be the position of Athira from the right?....
QA->A cyclist goes 40 km towards East and then turning to right he goes 40 km. Again he turn to his left and goes 20 km. After this he turns to his left and goes 40 km, then again turns right and goes 10km. How far is he from his starting point?....
QA->Right to vote in India is a constitutional right. Whicharticle of the Constitution gives this right?....
QA->Salim walked 100 meters facing towards south. From there he turned left and walked 40 meters. Thereafter, he turned to his left, walked 100m meters and stopped. How far and in what direction is Salim now from his starting point?....
QA->The standard firing order of a six cylinder in line left hand crank shaft is :....
MCQ->The simplest method of welding two pieces of metal together is known as pressure welding.The ends of a metal are heated to a white heat-for iron,the welding temperature should be about 1300C-in a flame.At this temperature the metal becomes plastic.The ends are pressed or hammered together,and the joint is smoothed off.Care must be taken to ensure that surfaces are thoroughly clean first,for dirt will weaken the weld.Moreover,the heating of iron or steel to a high temperature cause oxidation,and a film of oxide is added to the heated surfaces.For this reason,flux is applied to the heated metal.At welding heat,flux melts and the oxide particles are dissolved in it together with any other impurities which may be present.The metal surfaces are pressed together,and the flux is squeezed out from the center of the weld.A number of different types of weld may be used,but for fairly thick bars of metals,a vee-shaped belt should be normally employed.It is rather stronger than ordinary butt weld. The simplest way of welding two pieces of metal together is....
MCQ->What will be the output of the program? public class If1 { static boolean b; public static void main(String [] args) { short hand = 42; if ( hand < 50 && !b ) / Line 7 / hand++; if ( hand > 50 ); / Line 9 / else if ( hand > 40 ) { hand += 7; hand++; } else --hand; System.out.println(hand); } }....
MCQ-> Based on the information answer the questions which follow.A consultant to Department of Commerce. Government of Bianca has suggested 30 products which have high export potential. Dora an entrepreneur and prospective exporter notices that these products can be grouped in three ways- Machine made goods, Handmade goods and Intermediate goods. Among these 30 products some products are both machine made and intermediate goods but not handmade goods. Few products have a combination of handmade and machine made goods but not intermediate goods. Some products are handmade and intermediate goods but not machine made goods. Further it is seen that handmade-machine made goods are I less than machine made-intermediate goods. Similarly the total number of handmade-intermediate goods is I less than machine made-intermediate goods. There are just 4 products common across all product groups i.e. machine made-handmade- intermediate goods. Apart from this the number of only handmade goods is same as only machine made goods but less than only intermediate goods. Each product group/combination has at least one product. Dora prefers to export machine made goods and avoid hand made goods. She finds out that only handmade goods are twice the machine made-intermediate goods and the number of only intermediate goods is an even number. Whereas her close friend Sara prefers to export intermediate goods followed by only handmade goods.Sara and Dora prefer to export as many common products as possible in order to understand the regulatory conditions. Keeping their preferences intact, what is the maximum number of common products which can be exported by both of them?
 ....
MCQ->When the weld is made from left to right, it is known as back-hand welding.....
MCQ->In fore-hand welding, the angle between the welding torch and the work is __________ as compared to back-hand welding.....
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use
DMCA.com Protection Status Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...Privacy | Terms And Conditions