The transformer cores operating at microwave frequency ranges are generally made up of ?->(Show Answer!)

1. The transformer cores operating at microwave frequency ranges are generally made up of

Write Comment

Comments

Tags

Show Similar Question And Answers

QA->What is the commonly used radio wave frequency in the microwave ovens to heat food?....

QA->India recently decided to set up two test ranges for radar-based electronic warfare (EW) systems. The two test ranges will come up at?....

QA->Of which irom is Core of transformer made up?....

QA->Where is Society for Applied Microwave Electronic Engineering and Research situated ?....

QA->Where is Society for Applied Microwave Electronic Engineering and Research....

MCQ->The transformer cores operating at microwave frequency ranges are generally made up of....

MCQ-> Based on the information answer the questions which follow.A consultant to Department of Commerce. Government of Bianca has suggested 30 products which have high export potential. Dora an entrepreneur and prospective exporter notices that these products can be grouped in three ways- Machine made goods, Handmade goods and Intermediate goods. Among these 30 products some products are both machine made and intermediate goods but not handmade goods. Few products have a combination of handmade and machine made goods but not intermediate goods. Some products are handmade and intermediate goods but not machine made goods. Further it is seen that handmade-machine made goods are I less than machine made-intermediate goods. Similarly the total number of handmade-intermediate goods is I less than machine made-intermediate goods. There are just 4 products common across all product groups i.e. machine made-handmade- intermediate goods. Apart from this the number of only handmade goods is same as only machine made goods but less than only intermediate goods. Each product group/combination has at least one product. Dora prefers to export machine made goods and avoid hand made goods. She finds out that only handmade goods are twice the machine made-intermediate goods and the number of only intermediate goods is an even number. Whereas her close friend Sara prefers to export intermediate goods followed by only handmade goods.Sara and Dora prefer to export as many common products as possible in order to understand the regulatory conditions. Keeping their preferences intact, what is the maximum number of common products which can be exported by both of them?
....

MCQ-> Read the following discussion/passage and provide an appropriate answer for the questions that follow. Of the several features of the Toyota Production System that have been widely studied, most important is the mode of governance of the shop - floor at Toyota. Work and inter - relations between workers are highly scripted in extremely detailed ‘operating procedures’ that have to be followed rigidly, without any deviation at Toyota. Despite such rule - bound rigidity, however, Toyota does not become a ‘command - control system’. It is able to retain the character of a learning organizationIn fact, many observers characterize it as a community of scientists carrying out several small experiments simultaneously. The design of the operating procedure is the key. Every principal must find an expression in the operating procedure – that is how it has an effect in the domain of action. Workers on the shop - floor, often in teams, design the ‘operating procedure’ jointly with the supervisor through a series of hypothesis that are proposed and validated or refuted through experiments in action. The rigid and detailed ‘operating procedure’ specification throws up problems of the very minute kind; while its resolution leads to a reframing of the procedure and specifications. This inter - temporal change (or flexibility) of the specification (or operating procedure) is done at the lowest level of the organization; i.e. closest to the site of action. One implication of this arrangement is that system design can no longer be rationally optimal and standardized across the organization. It is quite common to find different work norms in contiguous assembly lines, because each might have faced a different set of problems and devised different counter - measures to tackle it. Design of the coordinating process that essentially imposes the discipline that is required in large - scale complex manufacturing systems is therefore customized to variations in man - machine context of the site of action. It evolves through numerous points of negotiation throughout the organization. It implies then that the higher levels of the hierarchy do not exercise the power of the fiat in setting work rules, for such work rules are no longer a standard set across the whole organization. It might be interesting to go through the basic Toyota philosophy that underlines its system designing practices. The notion of the ideal production system in Toyota embraces the following -‘the ability to deliver just - in - time (or on demand) a customer order in the exact specification demanded, in a batch size of one (and hence an infinite proliferation of variants, models and specifications), defect - free, without wastage of material, labour, energy or motion in a safe and (physically and emotionally) fulfilling production environment’. It did not embrace the concept of a standardized product that can be cheap by giving up variations. Preserving consumption variety was seen, in fact, as one mode of serving society. It is interesting to note that the articulation of the Toyota philosophy was made around roughly the same time that the Fordist system was establishing itself in the US automotive industry. What can be best defended as the asset which Toyota model of production leverages to give the vast range of models in a defect - free fashion?
....

MCQ->Match the following: Microwave Measuring Instruments Measurements EffectedA.Bolometer1.Reflection coefficientsB.VSWR meter2.Half power beam widthsC.Cavity wave meter3.Microwave powerD.Pattern recorder4.Microwave frequency

....

MCQ->Which of the following material is preferred for transformer cores operating in micro wave frequency range?....