1. Block diagram of a simple standard control system is shown below in the figure.Which of the following statement about the above control system is wrong ?





Write Comment

Type in
(Press Ctrl+g to toggle between English and the chosen language)

Comments

Tags
Show Similar Question And Answers
QA->Cylinder block construction by mono-block is preferred to individual cylinder construction because of?....
QA->A computer has 8 MB in main memory, 128 KB cache with block size of 4KB. If direct mapping scheme is used, how many different main memory blocks can map into a given physical cache block?....
QA->On November 30, 2014, the Simon Wiesenthal Center reported that a senior Nazi figure who centrally involved in the implementation of the Holocaust had died in Syria around 2010, or four years earlier. Who is that Nazi figure?....
QA->The number of relationships in which an entity can appear in an E-R diagram is called its:....
QA->A diagram of the heavens showing the relative position of planets at the time of a person's death....
MCQ-> Study the following information carefully and answer the questions given below : Eight friends - R, S, T, U, V, W. X and Y - are sitting around a circular table facing the centre, but not necessarily in the same order. Each of the them studies in the different Standards viz, Standard I to Standard VIII, but not necessarily in the same order. T is second to the right of the person who studies in Standard VII. Only one person sits between T and the person who studies in Standard V. X is sitting third to the left of the person who studies in Standard VIII. The person studying in Standard VIII is not an immediate neighbour of the person studying in Standard VII. T does not study in Standard VIII. The person studying in Standard VI is to the left of U. U does not study in Standard V or Standard VIII. The persons studying in Standard VI and VII are immediate neighbours of each other. One of the immediate neighbours of the person studying in Standard VIII, studies in Standard II. S and Y are immediate neighbours of each other. There is one person between S and R. V does not study in Standard I. R studies in Standard V. Y does not study in Standard II. W is sitting between the persons who study in Standard VII and Standard IV. X is second to the right of the person studying in Standard I.Who among the following is sitting third to the right of T.
 ....
MCQ->Block diagram of a simple standard control system is shown below in the figure.Which of the following statement about the above control system is wrong ?....
MCQ-> P, Q, R, S, T, V and W are seven students of a school. Each of them studies in different standard from Standard IV to Standard X not necessarily in the same order. Each of them has favourite subject from English, Science, History, Geography, Mathematics, Hindi and Sanskrit not necessarily in the same order. Q studies in VII Standard and does not like either Mathematics or Geography. R likes English and does not study either in V or in IX. T studies in VIII Standard and likes Hindi. The one who likes Science studies in X Standard. S studies in IV Standard. W likes Sanskrit. P does not study in X Standard. The one who likes Geography studies in V Standard.In which standard does W study ?
 ....
MCQ-> Applicants for the doctoral programmes of Ambi Institute of Engineering (AIE) and Bambi Institute of Engineering (BIE) have to appear for a Common Entrance Test (CET). The test has three sections: Physics (P), Chemistry (C), and Maths (M). Among those appearing for CET, those at or above the 80th percentile in at least two sections, and at or above the 90th percentile overall, are selected for Advanced Entrance Test (AET) conducted by AIE. AET is used by AIE for final selection.For the 200 candidates who are at or above the 90th percentile overall based on CET, the following are known about their performance in CET: 1. No one is below the 80th percentile in all 3 sections. 2. 150 are at or above the 80th percentile in exactly two sections. 3. The number of candidates at or above the 80th percentile only in P is the same as the number of candidates at or above the 80th percentile only in C. The same is the number of candidates at or above the 80th percentile only in M. 4. Number of candidates below 80th percentile in P: Number of candidates below 80th percentile in C: Number of candidates below 80th percentile in M = 4:2:1.BIE uses a different process for selection. If any candidate is appearing in the AET by AIE, BIE considers their AET score for final selection provided the candidate is at or above the 80th percentile in P. Any other candidate at or above the 80th percentile in P in CET, but who is not eligible for the AET, is required to appear in a separate test to be conducted by BIE for being considered for final selection. Altogether, there are 400 candidates this year who are at or above the 80th percentile in P.What best can be concluded about the number of candidates sitting for the separate test for BIE who were at or above the 90th percentile overall in CET?
 ....
MCQ->Which of the following statements are correct? The switch statement is a control statement that handles multiple selections and enumerations by passing control to one of the case statements within its body. The goto statement passes control to the next iteration of the enclosing iteration statement in which it appears. Branching is performed using jump statements which cause an immediate transfer of the program control. A common use of continue is to transfer control to a specific switch-case label or the default label in a switch statement. The do statement executes a statement or a block of statements enclosed in {} repeatedly until a specified expression evaluates to false.....
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use
DMCA.com Protection Status Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...Privacy | Terms And Conditions