1. When a ring of metal is heated what happens to its hole?





Write Comment

Type in
(Press Ctrl+g to toggle between English and the chosen language)

Comments

Tags
Show Similar Question And Answers
QA->A metal plate with a circular hole at the centre is heated. What will happen to the area of the hole?....
QA->A metal sheet with circular hole is heated. what change will be in the hole?....
QA->A hole is made in a brass plate and it is heated , the size of the hole will....
QA->What happens; When water is heated from °C to 10°C the volume of water?....
QA->What happens, When water is heated from °C to 10°C the volume of water?....
MCQ->The simplest method of welding two pieces of metal together is known as pressure welding.The ends of a metal are heated to a white heat-for iron,the welding temperature should be about 1300C-in a flame.At this temperature the metal becomes plastic.The ends are pressed or hammered together,and the joint is smoothed off.Care must be taken to ensure that surfaces are thoroughly clean first,for dirt will weaken the weld.Moreover,the heating of iron or steel to a high temperature cause oxidation,and a film of oxide is added to the heated surfaces.For this reason,flux is applied to the heated metal.At welding heat,flux melts and the oxide particles are dissolved in it together with any other impurities which may be present.The metal surfaces are pressed together,and the flux is squeezed out from the center of the weld.A number of different types of weld may be used,but for fairly thick bars of metals,a vee-shaped belt should be normally employed.It is rather stronger than ordinary butt weld. The simplest way of welding two pieces of metal together is....
MCQ->When a ring of metal is heated what happens to its hole?....
MCQ->In a rocket shape firecracker, explosive powder is to be filled up inside the metallic enclosure. The metallic enclosure is made up of a cylindrical base and conical top with the base of radius 8 centimeter. The ratio of height of cylinder and cone is 5:3. A cylindrical hole is drilled through the metal solid with height one third the height of the metal solid. What should be the radius of the hole, so that volume of the hole (in which gun powder is to be filled up) is half of the volume of metal solid after drilling?....
MCQ->In this question, a passage is given followed by a statement. Read the passage carefully and judge the statement based on the given passage. Using knives and shears, a pair of Russian spacewalkers on Tuesday cut samples of material around a mysterious hole in a Soyuz spacecraft docked on the International Space Station that a Moscow official suggested could have been deliberately sabotaged. The 2 mm cavity on the Soyuz spaceship docked at the ISS caused an air leak detected in August, two months after the craft’s last voyage. Roscosmos space agency said the aim was to discover whether the small but dangerous hole had been made on Earth or in space, to cut away the insulation covering the hole, take out a sample of the material around it to analyse and put new insulation over the area. Roscosmos chief stated that an investigation had ruled out a manufacturing error. The veteran cosmonauts struggled but eventually succeeded in their mission. Before this spacewalk, astronauts had only been able to examine the hole from inside the spacecraft. What made it especially hard is that the Soyuz spacecraft, unlike the ISS, was not designed to be repaired in spacewalks and has no outside railings for astronauts to hold onto. Statement: The mysterious hole in the Soyuz spacecraft is not due to manufacturing error.Choose the appropriate one from the following options A - The statement is definitely true. B - The statement is probably true. C - The statement cannot be determ ined. D - The statement is definitely false.....
MCQ-> DIRECTIONS for the following three questions: Answer the questions on the basis of the information given below.A city has two perfectly circular and concentric ring roads, the outer ring road (OR) being twice as long as the inner ring road (IR). There are also four (straight line) chord roads from E1, the east end point of OR to N2, the north end point of IR; from N1, the north end point of OR to W2, the west end point of IR; from W1, the west end point of OR, to S2, the south end point of IR; and from S1 the south end point of OR to E2, the east end point of IR. Traffic moves at a constant speed of $$30\pi$$ km/hr on the OR road, 20$$\pi$$ km/hr on the IR road, and 15$$\sqrt5$$ km/hr on all the chord roads.The ratio of the sum of the lengths of all chord roads to the length of the outer ring road is
 ....
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use
DMCA.com Protection Status Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...Privacy | Terms And Conditions