Toggle navigation
Home
Article Category
Question Papers
General Knowlege
Popular Pages
Multiple Choice Question in
Multiple Choice Question in 049
Multiple Choice Question in 2016
Multiple Choice Question in -current-affairs-2016
Multiple Choice Question in TRADES-INSTRUCTOR---GR-II---SMITHY---TECHNICAL-EDUCATION
Question Answer in ASSISTANT-PROFESSOR---COMPUTER-SCIENCE-AND-ENGINEERING---TECHNICAL-EDUCATION
Multiple Choice Question in ASSISTANT-PROFESSOR---COMPUTER-SCIENCE-AND-ENGINEERING---TECHNICAL-EDUCATION
Multiple Choice Question in english
Multiple Choice Question in abbreviations-abbreviations-m
Multiple Choice Question in SSC CHSL 7 March 2018 Morning Shift
Multiple Choice Question in 072/2016
Question Answer Bank
Multiple Choice Question Bank
Question Answer Category
Multiple Choice Question Category
Home
->
Multiple Choice Questions
1. In a PTB (Patellar Tendon Bearing) socket, all of the following are pressure tolerant areasexcept:
(A): Patellar tendon
(B): Gastronemius
(C): Fibular head
(D): Medial tibial flare
Previous Question
Show Answer
Next Question
Add Tags
Report Error
Show Marks
Write Comment
Type in
(Press Ctrl+g to toggle between English and the chosen language)
Post reply
Comments
Tags
kerala-psc
ASSISTANT-SURGEON-CASUALITY-MEDICAL-OFFICER--HEALTH-SERVICES-MEDICAL-OFFICER--KERALA-FACTORIES-ANS-BOILERS-SERVICE-ASSIS
81/2015
Show Similar Question And Answers
QA->The quadrantal bearing of a line is S40degree W; its whole circle bearing is :....
QA->The whole circle bearing of line is 300 degree , its quadrantal, bearing is :....
QA->If the fore bearing of a line is zero degree its back bearing is........degree.....
QA->If the magnetic bearing of a line is 35º 30´ the magnetic declination 3 º 30´ W, the true bearing of the line will be :....
QA->The purpose of a radiator pressure cap is to maintain the working pressure of a water cooling system.....
MCQ->In a PTB (Patellar Tendon Bearing) socket, all of the following are pressure tolerant areasexcept:....
MCQ->The following steps are involved in making a spigot and socket joint of cast iron pipes used in water supply systems :1. Tarred gasket or hemp yarn in wrapped around the spigot.2. The sipgot end is centered into the socket end of the preceding pipe.3. A joining ring end is placed around the barrel and against the face of the socket.4. The gasket or hemp yarn in caulked slightly.5. Molten pig lead is poured and then caulked.The correct sequence of these steps is....
MCQ->If the tendon is placed at an eccentricity e below the centroidal axis of the lon-gitudial axis of a rectangular beam (sectional modulus Z and stressed load P in tendon) the stress at the extreme top edge....
MCQ->The patella P located in the human knee joint is subjected to tendon forces T1 and T2 and a force F exerted on the patella by the femoral articular A. If the directions of these forces are estimated from an X-ray as shown, determine the magnitudes of T1 and F when the tendon force T2 = 6 lb.. The forces are concurrent at point O.....
MCQ->A rotor which is balanced statically but not dynamically is supported on two bearings L apart and at high speed of the rotor, reaction on the left bearing is R. The right side of the bearing is shifted to a new position 2 L apart from the left bearing. At the same rotor speed, dynamic reaction on the left bearing in the new arrangement will....
×
×
Type The Issue
×
Your Marks
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use
Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...
Privacy
|
Terms And Conditions