Toggle navigation
Home
Article Category
Question Papers
General Knowlege
Popular Pages
Multiple Choice Question in
Multiple Choice Question in 049
Multiple Choice Question in 2016
Multiple Choice Question in -current-affairs-2016
Multiple Choice Question in TRADES-INSTRUCTOR---GR-II---SMITHY---TECHNICAL-EDUCATION
Question Answer in ASSISTANT-PROFESSOR---COMPUTER-SCIENCE-AND-ENGINEERING---TECHNICAL-EDUCATION
Multiple Choice Question in ASSISTANT-PROFESSOR---COMPUTER-SCIENCE-AND-ENGINEERING---TECHNICAL-EDUCATION
Multiple Choice Question in english
Multiple Choice Question in abbreviations-abbreviations-m
Multiple Choice Question in SSC CHSL 7 March 2018 Morning Shift
Multiple Choice Question in 072/2016
Question Answer Bank
Multiple Choice Question Bank
Question Answer Category
Multiple Choice Question Category
Home
->
Multiple Choice Questions
1. A key connecting to a flange coupling to a shaft likely to fail in :
(A): tension
(B): shear
(C): torsion
(D): bending
Previous Question
Show Answer
Next Question
Add Tags
Report Error
Show Marks
Write Comment
Type in
(Press Ctrl+g to toggle between English and the chosen language)
Post reply
Comments
Tags
kerala-psc
2016
WORKS-MANAGER---STATE-WATER-TRANSPORT
049/2016
049
Show Similar Question And Answers
QA->A sliding mesh gearbox has a gear ratio 4:1 at the third gear position. The clutch shaft gear has 15 teeth and its mating lay shaft gear is having 45 teeth. If the main shaft gear contains 28 teeth, the mating lay shaft gear should have:....
QA->Which transmission unit is used to turn the driven shaft faster than the driving shaft?....
QA->If P1 can fail 50% of the times and P2, 40% of the times, P can fail -----------of the times.....
QA->Viscous coupling is employed instead of …………. in modern vehicles.....
QA->When a key is pressed on the key board, which standard is used for converting the keystroke into corresponding bits?....
MCQ->A key connecting to a flange coupling to a shaft likely to fail in :....
MCQ->Consider the following statements in respect of plate girders :1. A large number of cover plates are provided over flange angles so that curtailed flanges match the bending moment diagram exactly.2. At least one cover plate should extend over the entire span so that rain water may not enter and corrode the connections.3. A minimum of one-third of flange area should be provided in flange angles and balance in flange cover plates for stability.Which of the statements given above are correct ?....
MCQ->The 2-kg shaft CA passes through a smooth journal bearing at B. Initially, the springs, which are coiled loosely around the shaft, are unstretched when no force is applied to the shaft. In this position s = sª = 250 and the shaft is originally at rest. If a horizontal force of F = 5 kN is applied, determine the speed of the shaft at the instant s = 50 mm, sª = 450 mm. The ends of the springs are attached to the bearing at B and the caps at C and A.....
MCQ->Gross flange area for a riveted plate girder is to be designed considering net area as 80% of its gross area. Consider width of the flange as 500 mm while web plate as 1000 mm x 12 mm. The girder is to resist a maxi-mum BM of 4500 kNm. Maximum allowable bending stress in tension is 150 MPa. Gross flange area is....
MCQ->The following quantities refer to a channel section used as a beam : b = width of flange (upto centre of web thickness).h = depth of web (c/c of flange thickness). t = thickness of flange and web.I = moment of inertia of channel about xx axis.e = distance of shear centre, outside the channel from the mid thickness of the web.The value of 'e' is given by....
×
×
Type The Issue
×
Your Marks
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use
Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...
Privacy
|
Terms And Conditions