Toggle navigation
Home
Article Category
Question Papers
General Knowlege
Popular Pages
Multiple Choice Question in 049
Multiple Choice Question in
Multiple Choice Question in 2016
Multiple Choice Question in -current-affairs-2016
Multiple Choice Question in TRADES-INSTRUCTOR---GR-II---SMITHY---TECHNICAL-EDUCATION
Question Answer in ASSISTANT-PROFESSOR---COMPUTER-SCIENCE-AND-ENGINEERING---TECHNICAL-EDUCATION
Multiple Choice Question in ASSISTANT-PROFESSOR---COMPUTER-SCIENCE-AND-ENGINEERING---TECHNICAL-EDUCATION
Multiple Choice Question in english
Multiple Choice Question in abbreviations-abbreviations-m
Multiple Choice Question in SSC CHSL 7 March 2018 Morning Shift
Multiple Choice Question in 072/2016
Question Answer Bank
Multiple Choice Question Bank
Question Answer Category
Multiple Choice Question Category
Home
->
Multiple Choice Questions
1. A solid shaft is subjected to a bending moment and twisting moment of 3 kNm and 4 kNm respectively. The equivalent bending moment is ?
(A): 4 kNm
(B): 3 kNm
(C): 3.5 kNm
(D): 4.5 kNm
Previous Question
Show Answer
Next Question
Add Tags
Report Error
Show Marks
Write Comment
Type in
(Press Ctrl+g to toggle between English and the chosen language)
Post reply
Comments
Tags
kerala-psc
INSPECTOR-OF-FACTORIES-AND-BOILERS-GR-II---FACTORIES-AND-BOILERS
053/2016
Show Similar Question And Answers
QA->A sliding mesh gearbox has a gear ratio 4:1 at the third gear position. The clutch shaft gear has 15 teeth and its mating lay shaft gear is having 45 teeth. If the main shaft gear contains 28 teeth, the mating lay shaft gear should have:....
QA->Which transmission unit is used to turn the driven shaft faster than the driving shaft?....
QA->The maximum bending moment due to moving load on a simply supported beam, occurs:....
QA->A school has only three classes comprised of 40, 50 and 60 students respectively. In these classes, 10%, 20% and 10% students respectively passed in the examinations. What is the percentage of students passed in the examination from the entire school?....
QA->The resilience of a material is considered when it is subjected to :....
MCQ->A solid shaft is subjected to a bending moment and twisting moment of 3 kNm and 4 kNm respectively. The equivalent bending moment is ?....
MCQ->A shaft is subjected to fluctuating loads for which the normal torque (T) and bending moment (M) are 1000 N-m and 500 N-m respectively. If the combined shock and fatigue factor for bending is 1.5 and combined shock and fatigue factor for torsion is 2, then the equivalent twisting moment for the shaft is....
MCQ->A shaft of diameter D is subjected to a twisting moment (T) and a bending moment (M). If the maximum bending stress is equal to maximum shear stress developed, then M is equal to....
MCQ->Un-factored maximum bending moments at a section of a reinforced concrete beam resulting from a frame analysis are 50, 80, 120 and 180 kNm under dead, live, wind and earthquake loads respectively. The design moment (kNm) as per IS: 456-2000 for the limit state of collapse (flexure) is....
MCQ->Two shafts 'A' and 'B' are made of same material. The shaft 'A' is solid and has diameter D. The shaft 'B' is hollow with outer diameter D and inner diameter D/2. The strength of hollow shaft in torsion is __________ as that of solid shaft.....
×
×
Type The Issue
×
Your Marks
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use
Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...
Privacy
|
Terms And Conditions