Go To Top Reset
TRADESMAN---AUTOMOBILE-MECHANIC---TECHNICAL-EDUCATION Related Question Answers
1. During the compression stroke of a four stroke diesel engine, the piston compresses :
Air fuel mixture Atomised diesel Diesel Vapour Air
Disscuss This Question & Answer Add Tags Report Error Show Marks
2. The inventor of two stroke engine is :
Dugald Clark Rudolf diesel James Watt Nicolaus A Otto
Disscuss This Question & Answer Add Tags Report Error Show Marks
3. Theoritically during expansion process in a four stroke engine :
inlet valve opens and exhaust valve closes Inlet valve closes and exhaust valve opens Both valve remains closed Both valve remains opened
Disscuss This Question & Answer Add Tags Report Error Show Marks
4. The nominal volume of cylinder when piston is at TDC is called :
Stroke volumet Swept volume Clearence volume Suction volume
Disscuss This Question & Answer Add Tags Report Error Show Marks
5. Which of the following engine can operate at higher speed?
Square engine Over square engine Under square engine Steam engine
Disscuss This Question & Answer Add Tags Report Error Show Marks
6. The process of flushing out the products of combustion from the engine cylinder by fresh charge is known as :
Turbo charging Super charging Scavenging None of the above
Disscuss This Question & Answer Add Tags Report Error Show Marks
8. When the piston of a two stroke. Single cylinder engine move from BDC to TDC?
transfer port open and intake port closes exhaust port open and transfer port closes exhaust port and transfer port opens none of these
Disscuss This Question & Answer Add Tags Report Error Show Marks
10. The ratio of Brake thermal efficiency to indicated thermal efficiency is known as :
Mechanical efficiency Relative efficiency Air standard efficiency Calorific value efficiency
Disscuss This Question & Answer Add Tags Report Error Show Marks
11. Chemically correct air fuel mixture ratio for SI engine is around :
15:1. 9:1 1970-01-01 06:01:00 1970-01-01 12:01:00
Disscuss This Question & Answer Add Tags Report Error Show Marks
12. In Otto cycle, the addition of heat takes place at:
Constant pressure Constant volume Partially at constant pressure Any of the above
Disscuss This Question & Answer Add Tags Report Error Show Marks
13. Which of the following is true for a two stroke engine?
fuel efficiency is more than four stroke engine of same size higher oil consumption used for two wheelers only eco friendly
Disscuss This Question & Answer Add Tags Report Error Show Marks
14. Which type of nozzle can be used for facilitating pilot injection before the main injection?
Single hole nozzle Multi hole nozzle Pintle nozzle Pmtaux nozzle
Disscuss This Question & Answer Add Tags Report Error Show Marks
15. At the ventury throat of the Carburettor the velocity of air is :
Maximum Decreases Increases Remains same as before
Disscuss This Question & Answer Add Tags Report Error Show Marks
16. The condition at which the engine operates at no load and with nearly closed throttle is known as:
Dieseling Cruising Idling None of the above
Disscuss This Question & Answer Add Tags Report Error Show Marks
17. The reference fuels used for comparing the anti knock value of SI engine fuel is :
Benzene and tetraethyl lead Iso octane and normal heptane Normal cetane and alpha methyl naphathalene Benzene and iso octane
Disscuss This Question & Answer Add Tags Report Error Show Marks
18. Releasing of clutch pedal causes :
Load on release finger The compression of pressure spring Pressure plate move away from clutch disc Pressure plate move towards clutch disc
Disscuss This Question & Answer Add Tags Report Error Show Marks
19. Clutch shaft is also known as :
Transmission input shaft Counter shaft Lay shaft Main shaft
Disscuss This Question & Answer Add Tags Report Error Show Marks
20. Throw out bearing is used to :
reduce friction on clutch disc engage the clutch disengage the clutch none of the above
Disscuss This Question & Answer Add Tags Report Error Show Marks
21. Excess clutch free pedal play causes :
Clutch slipping Difficulty in gear shifting Wear of release bearing Wear of clutch disc
Disscuss This Question & Answer Add Tags Report Error Show Marks
22. Which of the following is not a function of final driveāof heavy vehicle?
final speed reduction power transmission reduction of torque none of the above
Disscuss This Question & Answer Add Tags Report Error Show Marks
23. Which of the following is not an advantage of overdrive?
Fuel economy - Increase of torque Reduced engine wear High vehicle speed at low engine speed
Disscuss This Question & Answer Add Tags Report Error Show Marks
25. The part of synchromesh gear box which is splined to the transmission output shaft is :
Synchroniser sleeve Synchroniser ring Mainshaft gear Synchroniser hub
Disscuss This Question & Answer Add Tags Report Error Show Marks
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use
Powered By:Omega Web Solutions © 2002-2017 Omega Education PVT LTD...Privacy | Terms And Conditions