Go To Top Reset
1022016 Related Question Answers
2. The ability of material to deform without breaking is called:
Plasticity Elasticity Ductility Malleability
Disscuss This Question & Answer Add Tags Report Error Show Marks
3. In an optical square the two mirrors are placed at an angle of:
25 Degree 35 Degree 45 Degree 55 Degree
Disscuss This Question & Answer Add Tags Report Error Show Marks
4. The movable parts that are cleaned and lubricated comes under the category of:
Field work Office work Designing work Care and adjustment of instrument
Disscuss This Question & Answer Add Tags Report Error Show Marks
5. GTS stands for:
Great triangle survey Great trignometrical survey Great traverse survey Great Tangential survey
Disscuss This Question & Answer Add Tags Report Error Show Marks
6. Plane table is centered over a station with the help of:
Spirit level Alidade Trough compass Plumbing fork with plumb-bob
Disscuss This Question & Answer Add Tags Report Error Show Marks
7. Which method is used for locating inaccessible objects?
Radiation Intersection Resection Traversing
Disscuss This Question & Answer Add Tags Report Error Show Marks
8. The construction in the storage headwork to discharge surplus water to down stream side safety is called:
Stuice Barrage Head regulator Spillway
Disscuss This Question & Answer Add Tags Report Error Show Marks
9. Tick the correct answer for the following :
1 km=100 metre 1 km=1000 metre 1 km=1000 cm 1 km=100 cm
Disscuss This Question & Answer Add Tags Report Error Show Marks
10. Over turning of vehicles on a curve can be avoided by using:
Transition curve Vertical curve Compound curve Mean curve
Disscuss This Question & Answer Add Tags Report Error Show Marks
11. Sea-saw is an example of:
First order lever Second order lever Third order lever Fourth order lever
Disscuss This Question & Answer Add Tags Report Error Show Marks
12. CPU stands for:
Chief Performance Unit Central Processing Unit Chief Processing Unit Central Performance Unit
Disscuss This Question & Answer Add Tags Report Error Show Marks
13. Which scale is used to read three dimensions?
Plane scale Diagonal scale Comparative scale Full scale
Disscuss This Question & Answer Add Tags Report Error Show Marks
14. Among the following who was not chairperson of National Commission for women?
Jayanthi Patnaik Poornima Advani Mira kumar Girija Vyas
Disscuss This Question & Answer Add Tags Report Error Show Marks
15. Which Constitutional amendment raised the number of Loksabha seats to 545?
16th(1963) 30th(1973) 31st(1973) 42th(1976)
Disscuss This Question & Answer Add Tags Report Error Show Marks
16. Who is known as ‘Dharmaraja’?
Ayilyam Tirunal Indukotha Varma Utram Tirunal Balarama Kartika Tirunal Rama Varma
Disscuss This Question & Answer Add Tags Report Error Show Marks
17. Which was not a work of Makthi Thangal?
Paropakari Sathyaprakasham Thurki Samacharam None of these
Disscuss This Question & Answer Add Tags Report Error Show Marks
18. Who among the following got Bharat Ratna before becoming the President of India?
Dr.Zakir Hussain V.V.Giri Fakhruddin Ali Ahmed Dr.Rajendra Prasad
Disscuss This Question & Answer Add Tags Report Error Show Marks
19. The art of determining and representing the relative heights or elevations of different points on the surface of the earth :
levelling surveying traversing balancing
Disscuss This Question & Answer Add Tags Report Error Show Marks
20. The main principle of surveying is two work form :
lower level to higher level higher level to lower level whole to part part to whole
Disscuss This Question & Answer Add Tags Report Error Show Marks
21. The longest chain line in chain surveying is called :
Base line Check line Tie line Traverse line
Disscuss This Question & Answer Add Tags Report Error Show Marks
22. ---------tape is used for the work of the highest precession.
Cloth tape Metallic tape Linen tape Invar tape
Disscuss This Question & Answer Add Tags Report Error Show Marks
23. ----------is used for enlargement and reduction of plans.
Planimeter Clinometer Pentagraph Lithograph
Disscuss This Question & Answer Add Tags Report Error Show Marks
24. In Surveyor’s compass zero degree is marked at---------end.
North South Northand South Eastand West
Disscuss This Question & Answer Add Tags Report Error Show Marks
25. The inclination of the magnetic needle with horizontal is known as :
Dip Declination Closing error Sighting error
Disscuss This Question & Answer Add Tags Report Error Show Marks
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use
Powered By:Omega Web Solutions © 2002-2017 Omega Education PVT LTD...Privacy | Terms And Conditions