<<= Back Next =>>
You Are On Multi Choice Question Bank SET 853

42651. In a diamond crossing, number of noses are





42652. If the stock rails are B.H. rails, the type of switch generally provided, is





42653. Bending of rail ends due to loose packing under a joint and loose fish Bolts, is known





42654. On Broad Gauge main lines with maximum traffic loads, the rail section preferred to, is





42655. If D is the distance between the parallel sidings and α is the angle of crossing, the distance between the noses of crossing measured parallel to the main track, is





42656. On B.G. tracks the distance of outer signal from station limit is kept






42657. The rails get out of their original positions due to insufficient expansion gap. This phenomenon is known





42658. Mr. W. Simms, the consulting Engineer to the Government of India recommended the gauge for Indian railways





42659. If absolute levels of rails at the consecutive axles A, B, and C separated by 1.8 metres are 100.505 m, 100.530 m, and 100.525 m respectively, the unevenness of rails, is





42660. A CST-9 sleeper consists of






42661. Charles Vignoles invented the flat footed rails in






42662. To design a cross-over between parallel tracks, the required components are :





42663. Guide angle as per the aerofoil theory of Kaplan turbine a blade design is defined as the angle between





42664. Ibn Battuta visited India in the :





42665. Who is considered as “The Grand Old Man of India”?





42666. Kurichiya leader in the Pazhassi revolt:





42667. Political pupil of Gopala Krishna Gokhale:





42668. An R.C.C. column is treated as long if its slenderness ratio is greater than






42669. The width of the flange of a T-beam should be less than





42670. The first five year plan started in India in:





42671. Cantilever retaining walls can safely be used for a height not more than






42672. If W is the load on a circular slab of radius R, the maximum circumferential moment at the centre of the slab, is



42673. For M 150 mix concrete, according to I.S. specifications, local bond stress, is






42674. If the average bending stress is 6 kg/cm2 for M 150 grade concrete, the length of embedment of a bar of diameter d according to I.S. 456 specifications, is






42675. Bottom bars under the columns are extended into the interior of the footing slab to a distance greater than





42676. The diameter of longitudinal bars of a column should never be less than






42677. The design of a retaining wall assumes that the retained earth






42678. Dimensions of a beam need be changed if the shear stress is more than





42679. The thickness of base slab of a retaining wall generally provided, is






42680. For a circular slab carrying a uniformly distributed load, the ratio of the maximum negative to maximum positive radial moment, is






42681. Thickened part of a flat slab over its supporting column, is technically known as





42682. An R.C.C. beam not provided with shear reinforcement may develop cracks in its bottom inclined roughly to the horizontal at






42683. The effective span of a simply supported slab, is





42684. The Slogan “Garibi Hatavo”introduced by:





42685. The minimum cube strength of concrete used for a prestressed member, is






42686. The number of treads in a flight is equal to





42687. A short column 20 cm x 20 cm in section is reinforced with 4 bars whose area of cross section is 20 sq. cm. If permissible compressive stresses in concrete and steel are 40 kg/cm2 and 300 kg/cm2, the Safe load on the column, should not exceed





42688. The reinforced concrete beam which has width 25 cm, lever arm 40 cm, shear force 6t/cm2, safe shear stress 5 kg/cm2 and B.M. 24 mt,





42689. In a beam the local bond stress Sb, is equal to


42690. According to I.S. : 456 specifications, the safe diagonal tensile stress for M 150 grade concrete, is






42691. A foundation rests on





42692. For initial estimate for a beam design, the width is assumed






42693. If R and T are rise and tread of a stair spanning horizontally, the steps are supported by a wall on one side and by a stringer beam on the other side, the steps are designed as beams of width





42694. The advantage of a concrete pile over a timber pile, is






42695. If the permissible compressive stress for a concrete in bending is C kg/m2, the modular ratio is





42696. If d and n are the effective depth and depth of the neutral axis respectively of a singly reinforced beam, the lever arm of the beam, is



42697. The width of the flange of a T-beam, which may be considered to act effectively with the rib depends upon






42698. Design of a two way slab simply supported on edges and having no provision to prevent the corners from lifting, is made by






42699. Design of R.C.C. simply supported beams carrying U.D.L. is based on the resultant B.M. at





42700. The transverse reinforcements provided at right angles to the main reinforcement





<<= Back Next =>>
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use
DMCA.com Protection Status Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...Privacy | Terms And Conditions