<<= Back Next =>>
You Are On Multi Choice Question Bank SET 1309

65451. The most stable biasing technique used is the





65452. Refer to this figure. The value of IB is





65453. What is the Q-point for a fixed-bias transistor with IB = 75 A, DC = 100, VCC = 20 V, and RC = 1.5 k?





65454. Emitter bias requires





65455. Refer to this figure. The value of DC is





65456. Refer to this figure. Assume that IC IE. Find VE.





65457. Refer to this figure. In the voltage-divider biased npn transistor circuit, if RC opens, the transistor is




65458. Which transistor bias circuit arrangement has poor stability because its Q-point varies widely with DC?





65459. What is the most common bias circuit?





65460. Refer to the given figure. The most probable cause of trouble, if any, from these voltage measurements would be





65461. Refer to this figure. Determine IC.





65462. At saturation the value of VCE is nearly ________, and IC = ________.





65463. Voltage-divider bias has a relatively stable Q-point, as does





65464. Refer to this figure. Assume IC IE. Determine the value of RC that will allow VCE to equal 10 V.





65465. The linear (active) operating region of a transistor lies along the load line below ________ and above ________.



65466. The input resistance of the base of a voltage-divider biased transistor can be neglected





65467. Refer to this figure. The value of IC is





65468. Which transistor bias circuit arrangement provides good Q-point stability, but requires both positive and negative supply voltages?





65469. Refer to this figure. Calculate the current I2.





65470. Refer to this figure. In the voltage-divider biased npn transistor circuit, if R1 opens, the transistor is




65471. Changes in DC result in changes in





65472. Collector-feedback bias provides very poor stability with negative feedback from collector to base.



65473. A transistor is operating in a linear fashion at saturation.



65474. Base biasing is common in relay driver circuits.



65475. The formula DC = IB/IC is correct.



65476. The base bias circuit arrangement provides poor stability because its Q-point varies widely with DC.



65477. A pnp transistor requires the same bias polarities as the npn transistor.



65478. The purpose of biasing is to establish a proper Q-point.



65479. The base bias circuit is not beta-dependent.



65480. Collector-feedback bias is another name for base bias.



65481. The input resistance at the base of a transistor is RIN DCIBRE.



65482. Clipping is the result of





65483. Which transistor bias circuit arrangement provides good stability using negative feedback from collector to base?





65484. Refer to the given figure. The most probable cause of trouble, if any, from these voltage measurements is





65485. What is the dc input resistance at the base of a BJT?





65486. What is the maximum temperature limit for liquid-crystal displays (LCDs)?





65487. Which of the following diodes is limited to the reverse-bias region in its region of operation?





65488. The majority of power diodes are constructed using ________.





65489. Which of the following is (are) diodes?





65490. What is the limit of peak current IP in tunnel diodes?





65491. What is the response time of LCDs?





65492. What is the typical level of change in resistance per degree change in temperature?





65493. What is the maximum peak voltage for tunnel diodes?





65494. This is an equivalent circuit for the ________ diode.




65495. Which of the following semiconductor materials is (are) used for manufacturing solar cells?





65496. Which of the following semiconductor materials is (are) used in the manufacturing of tunnel diodes?





65497. What is the power density received from the sun at sea level?





65498. The varicap diode has a transition capacitance sensitive to the applied reverse-bias potential that is a maximum at zero volts and decreases ________ with increasing reverse-bias potentials.




65499. For a 50-A unit, the PIV of the Schottky is about ________ compared to 150 V for the p-n junction variety.





65500. What metal(s) is(are) used in the construction of Schottky diodes?






<<= Back Next =>>
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use
DMCA.com Protection Status Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...Privacy | Terms And Conditions