1. The state of stress at a point in a loaded member is shown in the below figure. The magnitude of maximum shear stress is





Write Comment

Type in
(Press Ctrl+g to toggle between English and the chosen language)

Comments

Tags
Show Similar Question And Answers
QA->Routine is not loaded until it is called. All routines are kept on disk in a relocatable load format. The main program is loaded into memory and is executed. This type of loading is called:....
QA->If the dew point is below freezing; it is referred to which point?....
QA->If the dew point is below freezing, it is referred to which point?....
QA->On November 30, 2014, the Simon Wiesenthal Center reported that a senior Nazi figure who centrally involved in the implementation of the Holocaust had died in Syria around 2010, or four years earlier. Who is that Nazi figure?....
QA->Vehicle weight when it is not loaded with passengers and cargo, but inclusive of the weight of full tank is known as :....
MCQ-> Each of the questions below consists of a question andtwo statements numbered I and II given below it. You have to decide whether the data provided in the statements are suf icient to answer the question. Read both the statements and - Give answer a: if the data in Statement I alone are sufficient to answer the question, while the data in Statement II alone are not sufficient to answer the question. Give answer b: if the data in Statement II alone are sufficient to answer the question, while the data in Statement I alone are not sufficient to answer the question. Give answer c: if the data either in Statement I alone or in Statement II alone are sufficient to answer the question. Give answer d: if the data even in both Statements I and II together are not sufficient to answer the question. Give answer e: if the data in both Statements I and II together are necessary to answer the question. What is the position of point F with respect to point I ? I. Point G is 5 km east of point F. Point S is 5 km north of point G. Point H is the mid point of points G and S. Point I is to the south of point H in such a manner that point G is the mid-point of points H and I. II. Point A is 10 km east of point F. Point B is 5 km south of point A. Point H is the midpoint of points A and B. Point I is 5 km south of point H. Point I is to the east of point L at a distance of 5 km.....
MCQ->Point D is in which direction with respect to Point B? I) Point A is to the west of Point B. Point C is to the north of Point B. Point D is to the south of Point C. II) Point G is to the south of Point D. Point G is 4m. from Point B. Point D is 9m. from point B. III) Point A is to the west of Point B. Point B is exactly midway between Points A and E. Point F is to the south of Point E. Point D is to the west of Point F.....
MCQ->How far and in which direction is point L from point P ? I. Point M is 5 metre to the south of point L. Point N is 7 metre to the east of point M. Point O is 5 metre to the north of point N. Point P is 5 metre to the east of point O. II. Point L is 19 metre to the west of point S. Point S is 5 metre to the north of point R. Point Q is 7 metre to the west of point R. Point P is to the north of point Q such that point Q and point P form a straight line of 5 metres.....
MCQ->Consider the following statements :1. In a member subjected to uniaxial tensile force the maximum normal stress is the external load divided by the maximum cross-sectional area.2. When the structural member is subjected to uniaxial loading, the shear stress is zero on a plane where the normal stress is maximum.3. In a member subjected to uniaxial loading, the normal stress on the planes of maximum shear stress is less than the maximum.Of these statements :....
MCQ->How far is point M from point S I.Point S is 7m to the south of point M. Point T is 4m to the east of point S. Point P is 4m to the north of point T. Point Q is to the west of point P. II.Point R is 4m to the west of point Q. Point S is 4m to the north of point Q. Point X is 4m to the north of point R. Point M is 11 m to the east of point X.....
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use
DMCA.com Protection Status Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...Privacy | Terms And Conditions