Which one of the following is an example of plastic welding? ?->(Show Answer!)

1. Which one of the following is an example of plastic welding?

Write Comment

Comments

Tags

Show Similar Question And Answers

QA->Uniforms of fireman have been coated with a plastic so as to make them flame resistant. Which is the plastic form?....

QA->AndhraPradesh government has initiated to construct Agri-Plastic Park in which citythat should have Central Institute of Plastic Engineering and Technology?....

QA->Governmentof India has decided to print plastic currency notes. What type of plastic isthis?....

QA->which is the following is used in welding industry?....

QA->Which gas is Used for Welding:....

MCQ-> Read the following passage and answer the questions. Passage: A new paper published by Rochman and her colleagues in February, in the journal Ecology, sifts through past research on marine debris to assess the true extent of the environmental threat. Plenty of studies have sounded alarm bells about the state of marine debris: Rochman and her colleagues set out to determine how many of those perceived risks are real Often. Rochman says, scientists will wrap up a paper by speculating about the broader impacts of what they've found. Maybe their study has shown that certain seabirds eat plastic bags, for example, and the paper goes on to warn that whole bird populations are at risk of dying out. "But the truth was that nobody had yet tested those perceived threats." Rochman says. "There wasn't a lot of information." Rochman and her colleagues examined more than a hundred papers on the impacts of marine debris that were published through 2013. Within each paper. they asked what threats scientists had studied-366 perceived threats in all and what they'd actually found. In 83 percent of cases, the perceived dangers of ocean trash were proven true. In most of the remaining cases. the working group found the studies too shoddy to draw conclusions from—they lacked a control group, for example. or used faulty statistics. Strikingly. Rochman says, only one well-designed study failed to find the effect it was looking for, an investigation of mussels ingesting microscopic plastic bits. The plastic moved from the mussels' stomachs to their bloodstreams. scientists found. and stayed there for weeks—but didn't seem to stress out the shellfish. A lot of ocean debris is "microplastic," or pieces smaller than five millimetres. These may be the beads from a facial scrub. fibres shed by synthetic clothing in the wash. or eroded remnants of larger debris. Compared to the number of studies investigating large-scale debris. Roclunan's group found little research on the effects of these tiny bits. There are also, she adds, a lot of open questions about the ways that ocean debris can lead to sea-creature death. Many studies have looked at how plastic affects an individual animal or that animal's tissues or cells, rather than whole populations. And in the lab, scientists often use higher concentrations of plastic than what's really in the ocean. None of that tells us how many birds or fish or sea turtles could die form plastic pollution or how deaths in one species could affect that animal's predators, or the rest of the ecosystem. "We need to be asking more ecologically relevant questions." Rothman says. Usually, scientists don't know how disasters like oil spills or nuclear meltdowns will affect the environment until after they've happened. she says. "We don't ask the right questions early enough." But if ecologists can understand how the slow-moving disaster of ocean garbage is affecting ecosystems. they might be able to prevent things from getting worse.Which ONE of the following conclusions based on the examination of the hundred-odd papers on marine debris and its ecological impact by Rachman and her colleagues is NOT CORRECT?
....

MCQ->The simplest method of welding two pieces of metal together is known as pressure welding.The ends of a metal are heated to a white heat-for iron,the welding temperature should be about 1300C-in a flame.At this temperature the metal becomes plastic.The ends are pressed or hammered together,and the joint is smoothed off.Care must be taken to ensure that surfaces are thoroughly clean first,for dirt will weaken the weld.Moreover,the heating of iron or steel to a high temperature cause oxidation,and a film of oxide is added to the heated surfaces.For this reason,flux is applied to the heated metal.At welding heat,flux melts and the oxide particles are dissolved in it together with any other impurities which may be present.The metal surfaces are pressed together,and the flux is squeezed out from the center of the weld.A number of different types of weld may be used,but for fairly thick bars of metals,a vee-shaped belt should be normally employed.It is rather stronger than ordinary butt weld. The simplest way of welding two pieces of metal together is....

MCQ-> Study the following information and answer the questions. Seven people, namely, A, B, C, D, E, F and G have an appointment but not necessarily in the same order, on seven different months (of the same year) namely January, February, April, June, August, October and December. Each of them also likes a different activity namely Drawing, Singing, Painting, Boxing, Karate, Craft and Running but not necessarily in the same order. The one who likes Craft has an appointment on one of the months before April. Only two people have an appointment between the one who likes craft and the one who likes painting. Only one person has an appointment between the one who likes painting and the one who likes running The one who likes running has an appointment in a month which has 31 days. Only three people have an appointment between the one who likes running and E. G has an appointment on one of the months before E. G does not have an appointment in the month which has the least number of days. Only three people have an appointment between G and C. Only one person has an appointment between C and the one who likes Karate. The one who likes Karate has an appointment before C. The one who likes singing has an appointment immediately before B. B has an appointment in a month which has less than 31 days. Only one person has an appointment between A and F. A has an appointment before F. Only one person has an appointment between F and the one who likes drawing.Who amongst the following has an appointment before the one who has an appointment in December ?
....

MCQ->Pick out thể one word for - a secret arrangement....

MCQ->Projection welding & stud welding is categorised as the __________ welding.....