Toggle navigation
Home
Article Category
Question Papers
General Knowlege
Popular Pages
Multiple Choice Question in 049
Multiple Choice Question in
Multiple Choice Question in 2016
Multiple Choice Question in TRADES-INSTRUCTOR---GR-II---SMITHY---TECHNICAL-EDUCATION
Multiple Choice Question in -current-affairs-2016
Question Answer in ASSISTANT-PROFESSOR---COMPUTER-SCIENCE-AND-ENGINEERING---TECHNICAL-EDUCATION
Multiple Choice Question in ASSISTANT-PROFESSOR---COMPUTER-SCIENCE-AND-ENGINEERING---TECHNICAL-EDUCATION
Multiple Choice Question in english
Multiple Choice Question in abbreviations-abbreviations-m
Multiple Choice Question in SSC CHSL 7 March 2018 Morning Shift
Multiple Choice Question in 072/2016
Question Answer Bank
Multiple Choice Question Bank
Question Answer Category
Multiple Choice Question Category
Home
->
Multiple Choice Questions
1. The effective length of a weld, is taken as the actual length
(A): minus the size of weld
(B): minus twice the size of weld
(C): plus the size of weld
(D): plus twice the size of weld
(E): none of these.
Previous Question
Show Answer
Next Question
Add Tags
Report Error
Show Marks
Write Comment
Type in
(Press Ctrl+g to toggle between English and the chosen language)
Post reply
Comments
Tags
Show Similar Question And Answers
QA->What is the total earnings of a worker from the following data? Standard time for completing the job 50 hours. Actual time taken for completing the job 45 hours. Time rate is Rs.20 per hour, premium bonus is 60% of time saved.....
QA->A train of length 150 meters took 8 seconds to cross a bridge of length 250 meters. Time taken by the train to cross a telephone post is :....
QA->The most effective pesticide for general use against most garden pests is?....
QA->Right to Information Act became effective in India on:....
QA->Medicines are more effective; if they are used in which state?....
MCQ->The simplest method of welding two pieces of metal together is known as pressure welding.The ends of a metal are heated to a white heat-for iron,the welding temperature should be about 1300C-in a flame.At this temperature the metal becomes plastic.The ends are pressed or hammered together,and the joint is smoothed off.Care must be taken to ensure that surfaces are thoroughly clean first,for dirt will weaken the weld.Moreover,the heating of iron or steel to a high temperature cause oxidation,and a film of oxide is added to the heated surfaces.For this reason,flux is applied to the heated metal.At welding heat,flux melts and the oxide particles are dissolved in it together with any other impurities which may be present.The metal surfaces are pressed together,and the flux is squeezed out from the center of the weld.A number of different types of weld may be used,but for fairly thick bars of metals,a vee-shaped belt should be normally employed.It is rather stronger than ordinary butt weld. The simplest way of welding two pieces of metal together is....
MCQ->The strength of single fillet weld,having length of weld 1,weld size s and permissible stresses is:....
MCQ->The permissible stress in the fillet weld is 100 N/mm2. The fillet weld has equal leg lengths of 15 mm each. The allowable shearing load on the weldment per cm length of the weld is....
MCQ->The tensile strength of the welded joint for double fillet is (where s = Leg or size of the weld, l = Length of weld, and σt = Allowable tensile stress for weld metal)....
MCQ->The strength of single fillet weld,having length of weld 1,weld size s and permissible stress s is:....
×
×
Type The Issue
×
Your Marks
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use
Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...
Privacy
|
Terms And Conditions