Go To Top Reset
<<= Back
Next =>>
You Are On Multi Choice Question Bank SET 3274
163701. The cutting fluid mostly used for machining steelis:
(A): Water (B): Dry (C): Heavy oil (D): Soluble oil
163702. The point angle of a drill, for drilling stainless steel is
(A): 90° (B): 118° (C): 135° (D): 150°
163703. The steel widely used for making precision measuringinstruments is:
(A): Nickel steel (B): Nickel — Chromium steel (C): High speed steel (D): High carbon steel
163704. With the same tool life, the maximum material per minute is removed by :
(A): Increasing the feed rate (B): Decreasing the cutting speed (C): Increasing the cutting speed (D): Increasing the depth of cut
163705. The lead screw of a lathe has threads.
(A): single start (B): V. thread (C): double start (D): multi-start
163706. The least count of the vernier bevel protractor is :
(A): 6 minute (B): 7 minute (C): 8 minute (D): 5 minute
163707. Screw pitch gauge is mainly used to check :
(A): Boring (B): Used to check external and internal threads (C): Knurling (D): Under cutting
163708. An operation of embossing a diamond shaped pattern on the surface of work piece, is known
(A): Threading (B): Grooving (C): Knurling (D): Step cutting
163709. Drilling is an example of:
(A): multi cutting (B): oblique cutting (C): simple start cutting (D): orthogonal cutting
163710. A sine bar is specified by its :
(A): width (B): length (C): diameter (D): step
163711. What material is used to make scriber?
(A): Carbon tool steel (B): High carbon tool st (C): High speed steel (D): Mild steel
163712. Who is the founder of fundamental principle of screw cutting lathe?
(A): Henry Richards (B): Samuel (C): Henrimanslae (D): Wilson de Paul
163713. What is the angle of worm thread?
(A): 49° (B): 55° (C): 47° (D): 29°
163714. Formula for finding R.P.M. in British system :
(A): Cutting speed x 12 (B): Cutting speed x 24 DL (C): Cutting speed x 18 D (D): Cutting speed x 20 x D
163715. The operation of making a cone - shaped enlargement of the end of a hole is known as :
(A): counter - boring (B): spot facing (C): boring (D): counter - sinking
163716. Trepanning is an operation of:
(A): Making a cone - shaped enlargement of the end of a hole (B): Producing a hole by removing metal along the circumference of a hollow cutting tool (C): Smoothing and squaring the surface around a hole (D): Finishing a small diameter hole
163717. The washer is generally specified by its :
(A): Outer diameter (B): Thickness (C): Mean diameter (D): Hole diameter
163718. Low helix angle drills are preferred for drilling holes in :
(A): Copper (B): Aluminium (C): Plastics (D): Cast steel
163719. A tool used to with draw a drill from the sleeve is called:
(A): Drill puller (B): Brill drawer (C): Drill rotator (D): Drift
163720. The enlarging of an existing circular hole with a rotating single point tool is called:
(A): boring (B): reaming (C): drilling (D): knurling
163721. The grinding of long, slender shafts or bars is usually done by :
(A): In feedgrinding (B): End feed grinding (C): Through feed grinding (D): Speed grinding
163722. The cutting fluid mostly used for machining alloy steels is :
(A): water (B): sulphurised mineral oil (C): solubleoil (D): dry
163723. The trade name of a non ferrous cast alloy composed of cobalt, chromium and tungsten is called:
(A): stellite (B): diamond (C): cast iron (D): ceramic
163724. Tool signature consists of------
(A): Six (B): Four (C): Seven (D): Eight
163725. A grinding wheel is said to be of elements if it holds the Abrasive grains more securely.
(A): Soft grade (B): Hard grade (C): High grade (D): Medium grade
163726. The process of changing the shape of grinding wheel as it becomes worn due to breaking away of the abrasive and bond, is called :
(A): Turning (B): Facing (C): Boring (D): Dressing
163727. Chip breakers are used to :
(A): increase tool life (B): to minimise heat generation (C): remove chips from bed (D): 99break the chips into shortsegments
163728. The lathe spindles are usually made hollow and provided with :
(A): Internal taper (B): No taper (C): External taper (D): Step taper
163729. In order to achieve a specific surface finish in single point turning, the most important factor to be controlled is :
(A): feed (B): cutting speed (C): under cutting (D): depth of cut
163730. A Hacksaw blade is specified by its :
(A): Width (B): Number of teeth (C): Length (D): Material
163731. The instrument used to measure external and internal diameter of shafts, thickness and depth of holes is :
(A): Out side caliper (B): Vernier caliper (C): Inside caliper (D): Inside micrometer
163732. According to Indian standards, the total number of tolerance grades are :
(A): 18 (B): 14 (C): 13 (D): 8
163733. Formula for finding cutting speed in metric system :
(A): xDx RPM/100 (B): kDxRPM/2000 (C): xDxRPM/1000 (D): nDxRPM/1200
163734. ____type of sand is produced after the mechanical disintegration process.
(A): Mountain soil (B): Red soil (C): Black soil (D): Arid soil
163735. Gersoppa waterfalls originated from :
(A): Narmada (B): Mahanadi (C): Tapti (D): Sharavati
163736. Pannadiamond belt situated at:
(A): Gujarat (B): Rajasthan (C): Madhya Pradesh (D): Bihar
163737. In between two adjacent tides how much time would taken for?
(A): 10 hours 24 minutes (B): 11 hours 26 minutes (C): 13 hours 30 minutes (D): 12 hours 26 minutes
163738. Industrial Credit and Investment Corporation
(A): 1953 (B): 1955 (C): 1954 (D): 1951
163739. The National Bank for agriculture and recommendation of:
(A): B. Sivaraman Committee (B): Gopalram Committee (C): Chandra Sekharan Committee (D): Kamath Committee
163740. Which one of the following newspaper that was started by Rajaram Mohan Roy?
(A): Bengal Gazzette (B): Al-Hilal (C): Mirat-Ul-Akbar (D): The Statesman
163741. Universities of Calcutta, Bombay and Madras started by :
(A): Lord Wellington (B): Lord Irwin (C): Lord Canning (D): Lord Ripon
163742. In 1928 all parties conference held at Calcutta which has approved?
(A): CR Formula (B): Nehru Report (C): Swedeshi Movement (D): Non-CooperationMovement
163743. Mahatma Gandhi called Tagore as :
(A): Guro (B): Guru Dev (C): Rana (D): Pratap
163744. Who is the author of ‘Adwaitha Chintha Paddhathi’?
(A): Dr. Palppu (B): Chattambi Swamikal (C): Sree Narayana Guru (D): Mannath Padmanabhan
163745. V.T. Bhattathirippad wrote the book :
(A): Kunthalatha (B): Rajani Rangam (C): Ulakka (D): Premamrutham
163746. Who led Ezhava Memorial?
(A): Kumaranasan (B): Dr. P. Palppu (C): Vagbhatananda (D): Pandit Karuppan
163747. In 1910 which social reformer nominated to SreeMoolam Praja Sabha?
(A): Thycaud Ayya (B): Ayya Vaikundar (C): Ayyankali (D): Pandit Karuppan
163748. The founder of the newspaper Swadeshabhimani is:
(A): Swadeshabhimani Ramakrishna Pillai (B): Vakkom Muhammed Abdul Moulavi (C): Mannath Padmanabhan (D): Herman Gundart
163749. In 2016 COPA America Football Tournament, who won the Golden Boot Award?
(A): Lionel Messi (B): Christiano Ronaldo (C): Edurado Vargas (D): Lui Suaras.
<<= Back
Next =>>
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use
Powered By:Omega Web Solutions © 2002-2017 Omega Education PVT LTD...Privacy | Terms And Conditions