Go To Top Reset
<<= Back
Next =>>
You Are On Multi Choice Question Bank SET 2989
149451. Design used for denim fibre
(A): 3/1 twill (B): 1/2 twill (C): 2/2 twill (D): 1/3 twill
149452. A silk fabric constructed with a weft sateen figure on a warp satin or twill or plain ground called
(A): Brocade (B): Georgette (C): Muslin (D): Damask
149453. Which is not a function of geo textile?
(A): Separation (B): Filtration (C): Drainage (D): Protection
149454. The fibres not used for the production of military protective clothing
(A): Aramids (B): Kevlar (C): Carbon fibres (D): Polyurethane
149455. The most suitable weave for ballistic protective clothing is
(A): Plain weave (B): Satin weave (C): Twill weave (D): Basket weave
149456. What are the primary colours in pigment theory?
(A): Red,Green Blue (B): Yellow,Green,Blue (C): Blue,Yellow,Red (D): Red,Yellow,Blue
149457. The weave that produce longitudinal warp line in the cloth with fine sunken lines in between is called
(A): Repp weave (B): Pique (C): Bedford cord (D): Twill weave
149458. Function of positive feed in knitting is
(A): Yarn tension compensating device (B): To alter the stitch length (C): Regulate the amount of yarn feed (D): Minimizing the yarn waste
149459. If the needle is not raised and does not receive the new feed yarn,a loop form called
(A): Knit loop (B): Tuck loop (C): Held loop (D): Miss loop
149460. In a carding machine wire points arranged in opposite direction and move same direction with different speed;the action called
(A): Carding (B): Stripping (C): Dofting (D): Drafting
149461. State the function of presser
(A): To close the beard (B): To close the latch (C): To give return movement to the needle (D): To assist the guard cam
149462. Define sinker loop
(A): A loop in which the same thread crosses over itself (B): Length of yarn placed over the needle (C): The yarn connect two adjacent needle loop (D): The upper part of the loop produced by the needle
149463. Amount of water used for the insertion of weft in water jet loom
(A): 5-9 cc/pick (B): 1-4 cc/pick (C): 0.1-0.4 cc/pick (D): 0.5/0.9 cc/pick
149464. State the function of swing door mechanism
(A): Regulate the feed cotton (B): Regulate the speed of beater (C): Pre-opening of cotton (D): Blending of fibres
149465. The function of weft brake in projectile weaving machine is
(A): To stop the projectile (B): Holding weft supply package (C): For guiding yarn on weft accumulator drum (D): Applies tension to weft yarn at appropriate time
149466. A defect caused by hardened fluff or foreign matter into the fabric is called
(A): Goat (B): Ditry cloth (C): Patchiness (D): Reediness
149467. A loom truly termed ‘automatic’ must have the following mechanisms in addition to the essential mechanism
(A): Weft stop motion,warp stop motion and weft replenishment motion (B): Well stop motion,weft replenishment motion and positive warp let-off motion (C): Weft replenishment motion,positive take-up motion (D): Positive warp let-off motion,warp stop motion and weft replenishment motion
149468. The cause for nep formation in blow room
(A): Too high or low beater speed (B): High variation of trash in different cotton varieties in mixing (C): Uneven feeding of material to the feeder (D): Inadequate or high calendar roller pressure
149469. Place many number of plies of fabric one over other and aligned length and width of fabric together is called
(A): Pattern matching (B): Cloth alignment (C): Pattern loading (D): Spreading
149470. Function of feed dog in sewing machine
(A): Control the length of stitch (B): Hold the cloth firmly in stitching position (C): Help to move the cloth forward while sewing (D): Hold the thread in position from spool
149471. Dugdales terry motion working on the principle of
(A): Insertion of wire picks (B): Loose reed principle (C): Fast reed principle (D): By acting take up motion
149472. Two or more shuttle boxes fitted with both end of loom called
(A): Multiple box looms (B): Pick at will looms (C): Non skip box looms (D): Circular box looms
149473. Find the calculated production of plain loom running with 160 RPM,40 pick/inches with an efficiency of 75%
(A): 3 inches/minute (B): 3 inches/hour (C): 4 inches/minute (D): 5 inches/minute
149474. Warp yarns of one shed line do not cross all the yarns of other shed line at the same time.This is called
(A): Staggering of healds (B): Balancing of healds (C): Warp easing of healds (D): Balancing of shed
149475. A centre weft fork motion
(A): Check presence of weft in alternate picks (B): Check presence of weft in every picks (C): Used for the production of heavy duty fabric (D): Stops the loom when a end breaks
149476. The function of check strap is
(A): To control the picking force (B): Decrease the momentum of picker (C): Destroying the momentum of shuttle entered in shuttle box (D): To protect the buffer and the picker inside the shuttle box
149477. In dwell of tappet period means
(A): Loom will remain stationary (B): Health with remain stationary (C): Healds are level and beat up starts (D): Healds are begin to move for shed
149478. Temperature of the size in a sow box for cotton sizing
(A): 85+-5C (B): 98 5C (C): 92 2C (D): 100 2C
149479. Primary ingredients in sizing are
(A): Adhesives,softeners,antistatic agents (B): Lubricants,antistatic agents (C): Delinquescent,softeners,lubricants (D): Adhesives,softeners,antiseptic agents
149480. In apirn winding machine function of layer locking device is
(A): Control diameter of pirn (B): Give proper tension (C): Improve prin stability (D): Locking the bunch of yarn
149481. The main advantage of splicing is
(A): More strength in joints (B): Uniform diameter of yarn (C): Easy to handle (D): Higher production in winding
149482. In a drum winding machine
(A): Package RPM is decreases empty to full (B): Coils per traverse is constant (C): Produce close winding package (D): Package RPM constant empty to full
149483. In winding two and a half turn fully accelerated drum means
(A): Drum grove make 2.5 turn around the drum from one end to the other (B): Drum lays more yarn on the base than nose (C): The base of cone increases as package size increases (D): All the above
149484. When succeeding coils are widely spaced on the package,it is known as
(A): Close winding (B): Open winding (C): Cheese winding (D): Automatic winding
149485. In a right hand dobby first pick is controlled by
(A): Straight feeler and top hook (B): Bend feeler and top hook (C): Straight feeler bottom hook (D): Bend feeler and bottom hook
149486. Normal clearance in a parallel blade slub catcher for carded counts
(A): 1 to 1.5 time of yarn diameter (B): 1.5 to 2 times of yarn diameter (C): 2 to 2.5 times of yarn diameter (D): 2.5 to 3 times of yarn diameter
149487. Advantage of swinging blade type slub catcher over fixed blade
(A): Clearing 50% more fault (B): Cheap and easy to maintain (C): More sensitive to thin places (D): Slubs can get squeezed and passed through
149488. Advantage of early shedding is
(A): Less power consumption (B): Heavy wefting (C): Less strain in warp (D): Useful for light weight fabric production
149489. Which one is incidental waste in weaving
(A): Knotting waste (B): Process waste (C): Waste from package fault (D): Waste during changing pirm
149490. Narrow,bare and dense stripes running along the warp direction of fabric is called
(A): Warp streaks (B): Weft bar (C): Missing end (D): Float
149491. The depth of reed wire along the direction of warp yarn is known as
(A): Air space (B): Percentage air space (C): Wire thickness (D): Gauge number of reed wire
149492. Refractometer used for
(A): Measuring stretch in sizing (B): Determine size pick up (C): To indicate consistency of solid contents in size past (D): To measure saw box temperature
149493. The length and weight unit of Denier English count system
(A): Hank of 840 yards and 1 denier (B): Hank of 560 yards and 1 denier (C): Hank of 520 yards and 1 denier (D): Hank of 560 yards and 1 grains
149494. Count defined in Denier metric system as the
(A): Number of 9000-meter length units present in one gram (B): Number of one-gram weight units of yarn present in 9000 meters (C): Number of 1000 meters length units present in one gram (D): Number of one-gram weight units of yarn present in 1000 meters
149495. Heald count in a plain set is
(A): Number of heald eyes per 2 inches across the width (B): Number of heald eyes per inches across the width (C): Number of heald eyes per one inch width (D): Total number of heald eyes present in the heald divided by heald width
149496. Reed count is the number of dents in two inches in
(A): Radcliff system (B): Metric system (C): Brad ford system (D): Stokport system
149497. Tachometer used for measuring
(A): Moisture regain (B): RPM and surface speed (C): Percentage of elongation (D): Humidity
149498. If 200 yards of cotton yarn weigh 2 grams.What is the count in Ne?
(A): 100s (B): 24s (C): 45s (D): 54s
149499. The calculated count determined from the total length and total weight of different count termed as
(A): Resultant count (B): Average count (C): Universal count(tex) (D): Worsted count
149500. Find the resultant count of 8s,24s and 12s
(A): 8s (B): 15s (C): 4s (D): 20s
<<= Back
Next =>>
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use
Powered By:Omega Web SolutionsPrivacy | Terms And Conditions
Powered By:Omega Web Solutions