You Are On Multi Choice Question Bank SET 1883
94151. Large batches of parts may use statistical methods to control quality where a sample of parts is inspected.
94152. Tolerances of form and position are typically not used to control straightness.
94153. When lines intersect on a drawing at angles of this many degrees, it is customary not to dimension the angle:
94154. This is the term for the range of tightness or looseness resulting from the allowances and tolerances in mating parts:
94155. This is the measured size of a finished part:
94156. This means that a feature of a finished product contains the maximum amount of material permitted by the toleranced dimensions for that feature:
94157. This is the theoretically exact size from which limits of size are determined:
94158. In order to convert fractional inches into decimal inches ________.
94159. Referring to the fractional inches to decimal inches to millimeter conversion chart on page 55 what is the equivalent mm measurement of 3/16 inch.
94160. Some traditional board drafters preferred the drafting machine over the parallel straight edge because it could be used without the need for________.
94161. The first step in creating a traditional technical drawing is to ________.
94162. With some imagination, traditional drafters could actually produce a true 3-dimensional drawing.
94163. The parallel straight edge can be used for aligning the paper as well as drawing horizontal lines.
94164. Both the drafting machine and the parallel straight edge were used on specially designed tables to aid the drafter in producing technical drawings.
94165. When using a technical pencil to create a drawing the drafter would usually select a soft lead to create a very light line.
94166. A line to be drawn perpendicular to a horizontal line can only be drawn with a 45 degree triangle.
94167. An architect's scale is divided into 10ths of an inch.
94168. A drafter can use the 45 degree triangle to draw a 30 degree line.
94169. Every drafter and engineer continues to utilize both the architect and engineer's scales.
94170. Prior to the development of computer aided drafting, drafters relied on drawing boards, paper, and pencils to create technical drawings.
94171. A 15 degree line can be easily created by arranging both the 45 degree and 30/60 degree triangles.
94172. A half-moon protractor is divided into how many degrees?
94173. A line drawn with a long section, short dash, and another long section is a ________.
94174. Traditional drafters need to be able to create several different line widths because ________.
94175. Several of the tools used in traditional drafting include the following:
94176. A civil engineer working on a bridge design would probably rely on his ________ scale for checking printed drawings.
94177. Welding is often used for large structures that are difficult or impossible to fabricate entirely in a shop.
94178. Weldments are composed of a number of separate pieces fastened together as a unit.
94179. A seam weld is a type of arc and gas weld.
94180. The symbol for the desired weld is attached to the reference line, or shank, of the arrow.
94181. Groove weld size is usually specified on the welding symbol.
94182. In a welding drawing, joints are all shown as they would appear before welding.
94183. A fillet weld is a type of resistance weld.
94184. The usual fillet weld has equal legs.
94185. In a welding symbol, the arrow points to the joint where the weld is to be made.
94186. A groove weld is a type of arc and gas weld.
94187. Type of weld is typically not specified on the welding symbol.
94188. Welding is often more expensive when only one or a few identical parts are required.
94189. A spot weld is a type of resistance weld.
94190. Welding templates can simplify drawing welding symbols by hand.
94191. A projection weld is a type of:
94192. These weld symbols have no arrow-side or other-side significance:
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use
Powered By:Omega Web Solutions
94193. A back or backing weld is a type of:
© 2002-2017 Omega Education PVT LTD...Privacy | Terms And Conditions