Multi Option Question Page 1882

<<= Back Next =>>

You Are On Multi Choice Question Bank SET 1882

94101. The most important rule in freehand sketching is to keep the sketch in proportion.

94102. The degree of precision of a given sketch depends on its use.

94103. A set of written specifications is often included in a set of technical drawings.

94104. Drafters usually work alone in their cubical without any interaction with other drafters, designers, architects, or engineers.

94105. Modern computer drafters must have a thorough understanding of industrial drafting standards.

94106. This type of solid is egg-shaped and can be created by revolving an ellipse around one of its axes:

94107. Some of the common terms used to describe technical drawing include:

94108. The winding have many turns of thin wire in dc generator is:

94109. In oblique sketches, the most commonly used angles for receding lines are:

94110. A drafter who develops technical drawings of a highway overpass would most likely be a ________ drafter.

94111. This is the smallest diameter of a screw thread:

94112. This is the bottom surface joining the sides of two adjacent threads:

94113. ANSI has established three classes of fit.

94114. Keys can be used to prevent movement between shafts and wheels.

94115. Doubled threads are composed of two or more ridges running side by side.

94116. A screw thread is a ridge of uniform section in the form of a helix on the external or internal surface of a cylinder.

94117. The major diameter is the largest diameter of a screw thread.

94118. Pitch is equal to 12 divided by the number of threads per inch.

94119. Springs may be classified as either helical springs or flat springs.

94120. Rivets are not considered permanent fasteners.

94121. A machine pin is a mechanical device designed to store energy when deflected and to return the equivalent amount of energy when released.

94122. Tap drill depth does not include the cone point of the drill.

94123. Thread length, finish, and proportions are some of the standard characteristics of bolts and nuts.

94124. A torsion spring is a type of helical spring.

94125. An internal thread is a thread on the outside of a member.

94126. The axis of a screw is the longitudinal centerline through the screw.

94127. The root is the top surface joining the two sides of a thread.

94128. The form of a thread is the cross section of the thread cut by a plane containing the axis.

94129. Multiple threads are composed of one ridge, and the lead is equal to the pitch.

94130. A Class 3 fit is exceptionally high quality and recommended only when high cost of precision is warranted.

94131. These include taper pins, straight pins, dowel pins, clevis pins, and cotter pins:

94132. The distance a screw thread advances axially in one turn is the:

94133. The standard number of threads per inch for various diameters is the:

94134. This type of fit is high quality and is used for the bulk of interchangeable screw thread work:

94135. This type of thread is a thread on the inside of a member:

94136. Acceptable parts must not extend beyond this:

94137. This practice considers an individual part's dimensions and tolerances and that part's relation to its related parts:

94138. Defining the datum reference frame is necessary to apply GDT principles.

94139. Specific tolerances are based on the part's function and fit.

94140. Nominal size is used for general identification and is usually expressed in decimals.

94141. Unilateral tolerances have traditionally been given on angles.

94142. Geometric dimensioning and tolerancing can simplify the inspection process.

94143. Geometric tolerances state the maximum allowable variations of a form or its position from the perfect geometry implied in the drawing.

94144. In reference to geometric tolerancing, the term "geometric" refers to forms such as planes, cylinders, and squares.

94145. Implied 90 degree angles typically have different general tolerances applied to them than other angles covered by a general note.

94146. Datum surfaces and features are used as references to control other features.

94147. Allowance is the maximum clearance or minimum interference specified to achieve a fit between two mating parts.

94148. The ISO has its own system of preferred metric limits and fits.

94149. Increased precision makes parts less expensive to manufacture.

94150. Tolerance is the total amount a specific dimension is permitted to vary.

<<= Back Next =>> Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use

94101. The most important rule in freehand sketching is to keep the sketch in proportion. (adsbygoogle = window.adsbygoogle || []).push({});