Toggle navigation
Home
Article Category
Question Papers
General Knowlege
Popular Pages
Multiple Choice Question in 049
Multiple Choice Question in
Multiple Choice Question in TRADES-INSTRUCTOR---GR-II---SMITHY---TECHNICAL-EDUCATION
Multiple Choice Question in -current-affairs-2016
Question Answer in ASSISTANT-PROFESSOR---COMPUTER-SCIENCE-AND-ENGINEERING---TECHNICAL-EDUCATION
Multiple Choice Question in ASSISTANT-PROFESSOR---COMPUTER-SCIENCE-AND-ENGINEERING---TECHNICAL-EDUCATION
Multiple Choice Question in english
Multiple Choice Question in abbreviations-abbreviations-m
Multiple Choice Question in SSC CHSL 7 March 2018 Morning Shift
Multiple Choice Question in 072/2016
Multiple Choice Question in 100/2016
Question Answer Bank
Multiple Choice Question Bank
Question Answer Category
Multiple Choice Question Category
Home
->
Multiple Choice Questions
1. A back or backing weld is a type of:
(A): Groove weld
(B): Resistance weld
(C): Arc and gas weld
(D): Upset weld
Previous Question
Show Answer
Next Question
Add Tags
Report Error
Show Marks
Write Comment
Type in
(Press Ctrl+g to toggle between English and the chosen language)
Post reply
Comments
Tags
Show Similar Question And Answers
QA->Which type of rainfall occurs at places having continental type of climate?....
QA->Which type of cell has the ability to develop into any type of all?....
QA->Which type of cell has the ability to develop into any type of all ?....
QA->What is meant by the Idiom Behind ones back ?....
QA->The disease’die back of shoots’ is caused due to the deficiency of the micro element....
MCQ->The simplest method of welding two pieces of metal together is known as pressure welding.The ends of a metal are heated to a white heat-for iron,the welding temperature should be about 1300C-in a flame.At this temperature the metal becomes plastic.The ends are pressed or hammered together,and the joint is smoothed off.Care must be taken to ensure that surfaces are thoroughly clean first,for dirt will weaken the weld.Moreover,the heating of iron or steel to a high temperature cause oxidation,and a film of oxide is added to the heated surfaces.For this reason,flux is applied to the heated metal.At welding heat,flux melts and the oxide particles are dissolved in it together with any other impurities which may be present.The metal surfaces are pressed together,and the flux is squeezed out from the center of the weld.A number of different types of weld may be used,but for fairly thick bars of metals,a vee-shaped belt should be normally employed.It is rather stronger than ordinary butt weld. The simplest way of welding two pieces of metal together is....
MCQ-> Answer questions on the basis of information given in the following case. Bright Engineering College (BEC) has listed 20 elective courses for the next term and students have to choose any 7 of them. Simran, a student of BEC, notices that there are three categories of electives: Job - oriented (J), Quantitative - oriented (Q) and Grade - oriented (G). Among these 20 electives, some electives are both Job and Grade - oriented but are not Quantitative - oriented (JG type). QJ type electives are both job and Quantitative - oriented but are not Grade - oriented and QG type electives are both Quantitative and Grade - oriented but are not Job - oriented. Simran also notes that the total number of QJ type electives is 2 less than QG type electives. Similarly, the total number of QG type electives is 2 less than JG type and there is only 1 common elective (JQG) across three categories. Furthermore, the number of only Quantitative - oriented electives is same as only Job - oriented electives, but less than the number of only Grade - oriented electives. Each elective has at least one registration and there is at least one elective in each category, or combinations of categories.On her way back Simran met her friend Raj and shared the above information. Raj is preparing for XAT and is only interested in Grade - oriented (G) electives. He wanted to know the number of G - type electives being offered. Simran replied, “You have all the information. Calculate the number of G - type electives yourself. It would help your XAT preparation”. Raj calculates correctly and says that there can be _______ possible answers. Which of the following options would b est fit the blank above?
....
MCQ->A back or backing weld is a type of:....
MCQ->A circular plate 100 mm diameter is welded to another plate by means of 6 mm fillet weld. If the permissible shearing stress in the weld equals 10 kg/mm2, then the greatest twisting moment that can be resisted by the weld will be....
MCQ->The strength of single fillet weld,having length of weld 1,weld size s and permissible stresses is:....
×
×
Type The Issue
×
Your Marks
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use
Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...
Privacy
|
Terms And Conditions