Toggle navigation
Home
Article Category
Question Papers
General Knowlege
Popular Pages
Multiple Choice Question in 049
Multiple Choice Question in
Multiple Choice Question in TRADES-INSTRUCTOR---GR-II---SMITHY---TECHNICAL-EDUCATION
Multiple Choice Question in -current-affairs-2016
Question Answer in ASSISTANT-PROFESSOR---COMPUTER-SCIENCE-AND-ENGINEERING---TECHNICAL-EDUCATION
Multiple Choice Question in ASSISTANT-PROFESSOR---COMPUTER-SCIENCE-AND-ENGINEERING---TECHNICAL-EDUCATION
Multiple Choice Question in english
Multiple Choice Question in abbreviations-abbreviations-m
Multiple Choice Question in SSC CHSL 7 March 2018 Morning Shift
Multiple Choice Question in 072/2016
Multiple Choice Question in 100/2016
Question Answer Bank
Multiple Choice Question Bank
Question Answer Category
Multiple Choice Question Category
Home
->
Multiple Choice Questions
1. Refer to the given figure. A dc voltage of –1.2 V is applied. VCC = ±12 V. What is the output voltage?
(A): 1.2 V
(B): –1.2 V
(C): 0 V
(D): 12 V
Previous Question
Show Answer
Next Question
Add Tags
Report Error
Show Marks
Write Comment
Type in
(Press Ctrl+g to toggle between English and the chosen language)
Post reply
Comments
Tags
Show Similar Question And Answers
QA->The voltage regulator in the combined voltage and current regulator of a d.c charging circuit contains....
QA->On November 30, 2014, the Simon Wiesenthal Center reported that a senior Nazi figure who centrally involved in the implementation of the Holocaust had died in Syria around 2010, or four years earlier. Who is that Nazi figure?....
QA->When 177 freedom fighters were convicted to be hanged in the Chouri Choura case who appeared before the court and got acquitted 156 freedom fighters?....
QA->Idiom of 177. To come of age....
QA->...............refer to the amount spent on fuel, coal, diesel and fresh water used for the purpose of voyage.....
MCQ->Refer to the given figure. A dc voltage of –1.2 V is applied. VCC = ±12 V. What is the output voltage? ....
MCQ->It is suspected that the comparator in the figure given below has a problem. The inputs are activated in the table shown below and the corresponding outputs noted. What is most likely wrong with the circuit? For P0 – P3 = 1 and Q0 – Q3 = 0, P > Q = 1, P = Q = 1, P < Q = 0 For P0 – P3 = 0 and Q0 – Q3 = 1, P > Q = 0, P = Q = 1, P < Q = 1 For P0 – P3 = 1 and Q0 – Q3 = 1, P > Q = 0, P = Q = 1, P < Q = 0 ....
MCQ->Refer to the given figure. If an input signal of –0.5 V were applied, determine the output voltage. ....
MCQ->An op-amp has an open-loop gain of 90,000. Vsat = ±13 V. A differential voltage of 0.1 V p-p is applied between the inputs. What is the output voltage?....
MCQ->Refer the given figure. The outputs (Q0–Q3) of the memory are always LOW. The address lines (A0–A7) are checked with a logic probe and all are indicating pulse activity, except for A3, which shows a constant HIGH, and A7, which shows a constant LOW; the select lines, are checked and shows pulse activity, while indicates a constant HIGH. What is wrong, and how can the memory be tested to determine whether it is defective or if the external circuitry is defective? ....
×
×
Type The Issue
×
Your Marks
Terms And Service:We do not guarantee the accuracy of available data ..We Provide Information On Public Data.. Please consult an expert before using this data for commercial or personal use
Powered By:Omega Web Solutions
© 2002-2017 Omega Education PVT LTD...
Privacy
|
Terms And Conditions